Spyder

From LinkSprite Playgound
Revision as of 01:06, 25 September 2014 by Qian.zhang (talk | contribs) (Schematic)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search

Introduction

PLC-UART-LS is designed to transparently move serial data over the power line network at a speed of 2kbps, and achieves the target of replacing serial cables by the ubiquitous power line network.

On the PLC-UART-LS motherboard, there is a 20-pin receptacle. Users can choose different daughter boards, such as RS232, RS485, USB or Ethernet, based on the interface needs. The motherboard also support DIP by optional pins that can be used to directly plug to user's board without doing screwing.

PLC-UART-LS have built-in packet-level repeater function. This feature can greatly extend the coverage of the power line communication. PLC-UART-LS has both physical and logic addresses. In a network, both physical and logic addresses can be used to address different nodes in the network.

Modle:PLC-UART-LS

SPYDER1.jpg

Features

  • AC and DC power line Communications.
  • 5-24V wide range DC power supply.
  • Built-in opto-electronic coupling on the UART interface.
  • Fully transparent mode, plug and play coming out of the box without the need to do any programming.
  • Built-in error correction codes.
  • Built-in repeater function to extend the coverage.
  • Physical and logic address
  • AT commands used for advanced configuration.
  • UART interface to host uP
  • FSK(Frequency Shift Keying) modulation used in physical layer
  • Low power Design
  • RoHS
  • Small module size, and easy to be implemented into existing products.
  • 5V to 24V DC power supply

Application Ideas

  • AMR
  • Industry manufacture and control
  • Safeguard, fire alarm, smoke alarm
  • Collect and transmit instrument data
  • Safeguard and monitor
  • Home automation
  • Solar/Wind electricity generation system

Cautions

Schematic

Specification

Product Name Spyder Transceiver Module
Interface 3.3V TTL UART
Optional interface cards:
RS232 (model/ordering no: UART-RS232)
RS485 (model/ordering no: UART-RS485)
USB (model/ordering no: UART-USB)
Ethernet (model/ordering no: UART-Ethernet)
Zigbee (model: Xbee from Digi.com)
Communication Line Voltage 230VAC/50Hz
110VAC/60Hz
0-400V DC
Supply Voltage 7V–12V DC, Internal “ + ” External “ – ”
Modulation FSK(Frequency Shift Keying)
Carrier frequency 262K/144KHz
Error connection FEC(Forward Error Correction)
Data rate on powerline 30 Kbps
Maximum packet data length 300 bytes
Repeat Hops 3 Hops
Transmission distance 300 feets(No Repeater)
Support nodes number 65535
LED Power Line Activity LED/System LED/Serial port LED

Pin definition and Rating

Mechanic Dimensions

Usage

Hardware Installation

0046.jpg

You need to have a pair of the items shown above:

  • 1.Spyder
  • 2.RS232 card or USB card
  • 3.Power line cable used to couple power communication signal to power line, the power line can be 110V/220V 50/60Hz, DC, or unpowered.
  • 4.110V/220V to 12V/500mA power supply

Programming

You need to install LinkSprite-NEC serial port terminal software that is included in the CD that accompanies the Spyder by clicking setup.exe

If you are using a USB to RS232 converter, you can use Device Manager tab to find out the COM port.

2614.jpg

Open LinkSprite-NEC serial port terminal by click program and follow the following

2632.jpg

LinkSprite-NEC serial port terminal will show up as:

2649.jpg

Click the “Port Settings” button to configure the serial port:

2709.jpg

From device manager, we know that the COM port we are using is COM17. The default baud rate for Spyder is 9600. Click “OK”, and Click “Open COM Port” to open the COM port.

As shown in the following screen, by typing three ‘+’ fast, we can enter into AT command mode to configure the module.


2732.jpg

Next we can click “Start Continuous Send” to toggle continuous send and receive

FAQ

Q:What's the difference between Mamba and Spyder?

A:Spyder has a MCU Controller,Mamba doesn’t.

Support

If you have questions or other better design ideas, you can go to our forum to discuss or creat a ticket for your issue at linksprite support.

Resources

How to buy

Here to buy spyder:UART over Narrow Band Powerline Communication Modem SPYDER on LinkSprite Cart

See Also

Other related products and resources.

Licensing

This documentation is licensed under the Creative Commons Attribution-ShareAlike License 3.0 Source code and libraries are licensed under GPL/LGPL, see source code files for details.