Difference between revisions of "ATWIN Quad-band GPRS/GSM Shield for Arduino"
Katherine.d (talk | contribs) (→Schematic) |
Katherine.d (talk | contribs) (→Hardware Installation) |
||
| Line 29: | Line 29: | ||
=== Hardware Installation === | === Hardware Installation === | ||
| + | |||
| + | The shield must be powered by a wall adapter with 12V, 1A, like this one: [http://www.cutedigi.com/tools/power-supply/wall-adapter-power-supply-12vdc-1a.html PW-12VDC-1A_X3] | ||
| + | |||
| + | *RX jump to MRX, TX jump to MTX, and remove the atmega328P from arduino. By doing this, we can directly monitor serial port output using the USB port.The default baud rate is 115200. | ||
| + | |||
| + | *Install X-CTU serial terminal console:[http://www.cutedigi.com/pub/software/setup_xctu_5100.exe setup_xctu_5100.exe] | ||
| + | |||
| + | *Now we are going to use atmega328P's UART to talk to USB, and soft serial of atmega328P to talk to ATWIN. | ||
| + | |||
| + | *Before we do that, we have to change ATWIN's data rate to 9600 as soft serial can't go to 119200.In first tutorial setup, do: AT+IPR=9600 to set the baud rate to 9600 | ||
| + | |||
| + | *Now set the jumper RX to D3, and TX to D2. SO that atmega328P's UART to talk to USB and soft serial of atmega328P to talk to ATWIN: | ||
=== Programming === | === Programming === | ||
Revision as of 09:42, 8 November 2012
Contents
Introduction
AT139 is an ultra compact and high quality wireless module base on infineon UCL2 platform with industy-standard interface. This is a SMT package with small dimension, low power consumption, quad-band (AT139) and dual-band (AT139D) GSM/GPRS module, it can provide with voice, SMS, Fax, data applicationgs for customers.
Model: SOLID_ATGPRS_SHIELD_D32
Features
Application Ideas
Cautions
The warnings and wrong operations possible cause dangerous.
Schematic
Specification
May include key specification and other specifications.
Pin definition and Rating
Mechanic Dimensions
Usage
Hardware Installation
The shield must be powered by a wall adapter with 12V, 1A, like this one: PW-12VDC-1A_X3
- RX jump to MRX, TX jump to MTX, and remove the atmega328P from arduino. By doing this, we can directly monitor serial port output using the USB port.The default baud rate is 115200.
- Install X-CTU serial terminal console:setup_xctu_5100.exe
- Now we are going to use atmega328P's UART to talk to USB, and soft serial of atmega328P to talk to ATWIN.
- Before we do that, we have to change ATWIN's data rate to 9600 as soft serial can't go to 119200.In first tutorial setup, do: AT+IPR=9600 to set the baud rate to 9600
- Now set the jumper RX to D3, and TX to D2. SO that atmega328P's UART to talk to USB and soft serial of atmega328P to talk to ATWIN:
Programming
FAQ
Please list your question here:
Support
Resources
How to buy
Here to buy ATWIN Quad-band GPRS/GSM Shield for Arduino SOLID_ATGPRS_SHIELD_D32 on LinkSprite Cart
See Also
Other related products and resources.
Licensing
This documentation is licensed under the Creative Commons Attribution-ShareAlike License 3.0 Source code and libraries are licensed under GPL/LGPL, see source code files for details.
